Showing posts with label BJT. Show all posts
Showing posts with label BJT. Show all posts
[youtube]http://www.youtube.com/watch?v=g_BfQZtjJZ4[/youtube]
Part 1
All amplifier typically exhibit a band-pass frequency response. The cut off frequency in the low end is usually determined by the coupling band bypass capacitor .and the high frequency limit is typically determined by internal capacitances in the transistor itself.
Part 2:
[youtube]http://www.youtube.com/watch?v=1OKtejD225Y[/youtube]
Part 1:
BJT Amplifier
During normal operation, a potential is applied across the base/emitter junction so that the base is approximately 0.6v more positive than the emitter, this makes the base/emitter junction forward biased.
During normal operation, a potential is applied across the base/emitter junction so that the base is approximately 0.6v more positive than the emitter, this makes the base/emitter junction forward biased.
A much higher potential is applied across the base/collector junction with a relatively high positive voltage applied to the collector, so that the base/collector junction is heavily reverse biased. This makes the depletion layer between base and collector quite thick once power is applied.
As mentioned above, the collector is made up of mainly low resistivity material with a layer of high resistivity material next to the base/collector junction. This means that most of the voltage between collector and base is developed across this high resistivity layer, giving a high voltage gradient near the collector base junction.
When the base emitter junction is forward biased, a small current will flow into the base. Therefore holes are injected into the P type material. These holes attract electrons across the forward biased base/emitter junction to combine with the holes. However, because the emitter region is very heavily doped, many more electrons cross into the base region than are able to combine with holes. This means there is a large concentration of electrons in the base region and most of these electrons are swept straight through the very thin base, and into the base/collector depletion layer. Once here, they come under the influence of the strong electric field across the base/collector junction. This field is so strong due to the potential gradient in the collector material mentioned earlier, that the electrons are swept across the depletion layer and into the collector material, and so towards the collector terminal.
Varying the current flowing into the base, affects the number of electrons attracted from the emitter. In this way very small changes in base current cause very large changes in the current flowing from emitter to collector, so current amplification is taking place.
Part 2:
Part 2:
[youtube]http://www.youtube.com/watch?v=0C4uxtS-tlQ[/youtube]
How a Bipolar Junction Transistor Works
[youtube]http://www.youtube.com/watch?v=wT8fZJIl3Nk[/youtube]
Q. Why do we study small signal analysis of BJT, MOSFET, etc.What applications do they have?
Ans. We basically use small signal analysis in order to find a linear model for non-linear devices ( e.g. BJT, MOSFETs, Diodes ) . Non-linear means that these devices depend on the current passing through them, unlike resistors for example which are linear, their resistivity is constant regardless of the current passing through.
If we consider BJTs, we usually find the bias currents at DC, these values for DC currents ( emitter, collector and base currents ) can be used to determine the internal resistances of the transistor ( eg. r(pi), g(m) ) for those certain values of currents.
When we determine these resistance values, we can then replace the BJT with a linear model (e.g Hybrid or T model) by using this model we can treat the transistor as any other linear device in our analysis.
We can use small signal anaysis for many reasons such as finding the gain of amplifiers.
If we consider BJTs, we usually find the bias currents at DC, these values for DC currents ( emitter, collector and base currents ) can be used to determine the internal resistances of the transistor ( eg. r(pi), g(m) ) for those certain values of currents.
When we determine these resistance values, we can then replace the BJT with a linear model (e.g Hybrid or T model) by using this model we can treat the transistor as any other linear device in our analysis.
We can use small signal anaysis for many reasons such as finding the gain of amplifiers.
[youtube]http://www.youtube.com/watch?v=xY4_mJk6QAk[/youtube]
Part 1:
Biasing in electronics is the method of establishing predetermined voltages and/or currents at various points of an electronic circuit to set an appropriate operating point. The operating point of a device, also known as bias point, quiescent point, or simply Q-point, is the point on the output characteristics that shows the direct current (DC), collector-emitter voltage (VCE), and the collector current (IC) with no input signal applied. The term is normally used in connection with devices such as transistors.
Note: Use Internet Download Manager For Download these videos.
Subscribe to:
Posts (Atom)
